[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
draft-ietf-sacred-protocol-bss-04.txt
All,
I've just posted my working version as -04. Since it sometimes
takes a while for drafts to pop back out when we're this close
to the cutoff date, here's a copy in case you want to do some
reading soon.
Stephen.
--
____________________________________________________________
Stephen Farrell
Baltimore Technologies, tel: (direct line) +353 1 881 6716
39 Parkgate Street, fax: +353 1 881 7000
Dublin 8. mailto:stephen.farrell@xxxxxxxxxxxx
Ireland http://www.baltimore.com
INTERNET-DRAFT Editor: Stephen Farrell
expires in six months Baltimore Technologies
November 2002
Securely Available Credentials Protocol
<draft-ietf-sacred-protocol-bss-04.txt>
Status of this Memo
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of [RFC2026].
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts. Internet-Drafts are draft documents valid for a maximum of
six months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet- Drafts
as reference material or to cite them other than as "work in
progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
This document describes a protocol the secure up- and down-load of
cryptographic credentials. Discussion of this draft is taking place
on the SACRED mailing list of the IETF SACRED working group (see
http://www.imc.org/ietf-sacred for subscription information).
Table Of Contents
Status of this Memo.............................................1
Abstract........................................................1
Table Of Contents...............................................1
1. Introduction.................................................2
2. The protocol.................................................3
3. BEEP Profile for SACRED......................................8
4. IANA Considerations.........................................10
5. Security Considerations.....................................11
References.....................................................12
Acknowledgements...............................................13
Editor's Address...............................................13
Full Copyright Statement.......................................14
Appendix A: XML Schema.........................................14
Appendix B: An Example of Tuning with BEEP.....................17
Appendix C: Provision SACRED using other Protocols.............19
Appendix D: Changes & Open Issues..............................19
Editor: Farrell [Page 1]
INTERNET-DRAFT November 2002
1. Introduction
We describe a protocol whereby a user can acquire cryptographic
credentials (e.g., private keys, PKCS #15 [PKCS15] structures) from
a credential server, using a workstation that has locally trusted
software installed, but with no user-specific configuration. This is
somewhat less secure than a smart card, but can be used until smart
cards and smart card readers on workstations become ubiquitous, and
can be useful even after smart cards are ubiquitous, as a backup
strategy when a user's smart card is lost or malfunctioning.
The protocol's payloads are described in XML. This memo also
specifies a BEEP [BEEP] profile of the protocol. The protocol sets
out to meet the requirements in [REQS]. In particular, security
requirements in [REQS] are met by mandating support for TLS [TLS]
and/or DIGEST-MD5 [DIGEST-MD5].
We assume the only authentication information available to the user
is a username and password.
Many user-chosen passwords are vulnerable to dictionary attacks. So
this protocol is designed to give no information with which an
attacker can acquire information for launching a dictionary attack,
whether by eavesdropping or by impersonating either the client or
server.
The protocol also allows a user to create or delete an account,
change her account password and/or credentials and upload the new
values to the server. The protocol ensures that only someone that
knew the old account password is able to modify the credentials as
stored on the credential server. The protocol does not preclude
configuring a server to disallow some operations (e.g. credential
upload) for some users. The account management operations as a whole
are optional to implement for both credential servers and clients.
Note that there are potentially two "passwords" involved when using
this protocol - the first used to authenticate the user to the
credential server, and the second to decrypt (parts of) the
credential following a download operation. Where the context
requires it, we refer to the former as the account password and the
latter as the credential password.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in
this document are to be interpreted as described in [RFC2119].
Editor: Farrell [Page 2]
INTERNET-DRAFT November 2002
2. The protocol
This section defines the account management and "run-time"
operations for the SACRED protocol.
It also describes the message formats used, which are described in
XML [XMLSCHEMA]. Appendix A provides an XML schema for these
elements.
The approach taken here is to define SACRED elements that are
compatible with the elements used in [XKMS] and [XMLDSIG], so that
an implementation of this protocol can easily also support XKMS, and
vice versa.
It is also intended that other SACRED protocol instances (e.g. using
a different authentication scheme, credential format or transport
protocol) could re-use many of the definitions here.
2.1 Account management operations
These operations MAY be implemented, that is, they are OPTIONAL.
2.1.1 Information Request
This operation does NOT REQUIRE authentication.
The purpose of this operation is to provide to the client the values
required for account creation.
The client sends an InfoRequest message (which has no content).
The server responds with an InfoResponse message which contains the
authentication mechanism parameters for the server and the list of
supported ProcessInfo types. For DIGEST-MD5 this consists of the
list of realms (each as an XML element named "Realm") which the
server supports. There MUST be at least one realm specified. Clients
MUST be able to select one from a list of Realms and MUST be able to
disregard any other information present (allowed for extensibility).
2.1.2 Create Account
This operation REQUIRES server authentication.
The purpose of this operation is to setup a new account on the
server. The information required for a "new" account will depend on
the SASL [SASL] mechanism used.
The client sends a CreateAccountRequest, which contains the account
name (e.g. username). It also contains the elements required to
create an account for a particular authentication mechanism. The
actual information is defined according to the authentication
mechanism. For DIGEST-MD5 this consists of the password verifier
(the hashed username, password and realm) and the chosen realm.
Editor: Farrell [Page 3]
INTERNET-DRAFT November 2002
Although more than one set of such data is allowed by the data
structures defined in the appendix, clients SHOULD only include one
here.
The server responds with an error or acknowledgement message.
2.1.3 Remove Account
This operation REQUIRES mutual authentication.
The purpose of this operation is to delete the entire account.
The client sends a RemoveAccountRequest message (which has no
content) to the server.
The server MUST delete all information relating to the account and
respond with an error or acknowledgement message.
2.1.4 Modify Account
This operation REQUIRES mutual authentication.
The purpose of this operation is to allow the client to change the
information required for authentication. The information required
will depend on the authentication method used.
The client sends a ModifyAccountRequest message which contains the
elements required to change the authentication information for the
account, for a particular authentication mechanism. The actual
information is defined according to the authentication mechanism.
For [DIGEST-MD5] it will consist of a realm and password verifier
value.
Once the account information has been changed, the server will
respond with an error or acknowledgement message.
2.2 "Run-time" operations
These operations MUST be supported by all conformant
implementations.
2.2.1 Credential Upload
This operation REQUIRES mutual authentication.
The purpose of this operation is to allow the client to deposit a
credential with the server, or to delete one or more credentials
associated with the account.
The client sends an UploadRequest message to the server which can
contain zero or one Credential. If the UploadRequest contains no
Credential and the UploadRequest contains a "Delete="yes""
Editor: Farrell [Page 4]
INTERNET-DRAFT November 2002
attribute, then the all the credentials associated with that account
are deleted.
If a credential with the same credential selector field as in the
UploadRequest, (a "matching" credential), already exists for the
account, then that credential is replaced with the new credential
from the UploadRequest. Otherwise a "new" credential is associated
with that account.
If the new credential from the UploadRequest contains no PayLoad
field and the new credential has a "Delete="yes"" attribute, then
the (one and only) "matching" credential is deleted.
The processing of the "Delete" attribute MUST be strict – that is,
this attribute MUST be ignored unless it is set on a data structure
(either UploadRequest or Credential) which contains no useful value,
and the value of the attribute MUST be precisely "yes", any other
string value MUST be ignored.
If no "matching" credential exists, the server returns an error.
If any change is made to the stored credentials associated with the
account then the server MUST update the corresponding LastModified
value (returned in DownloadResponse messages) to the current time
(at the server).
The LastModified value in the UploadRequest MUST be the value which
was most recently received in a corresponding DownloadResponse for
that credential. This means the clients are strongly RECOMMENDED to
only produce an UploadRequest based on recently downloaded
credentials, since otherwise the LastModified value may be out of
date.
The LastModified value can also be of use in detecting conflicts.
For example, download to platform A, download to platform B, update
from B, update from A. The server could detect a conflict on the
second upload. In this case the server MUST respond with a BEEP
error (which SHOULD be StaleCredential).
The server MUST replace this with the current time at the server
before storing the credential however. (Note that this means that it
would be unwise for a client to include the LastModified field in a
ClientInfo digital signature which is calculated over the
CredentialType.)
The server responds with an error or acknowledgement message.
2.2.2 Credential Download
This operation REQUIRES mutual authentication.
Editor: Farrell [Page 5]
INTERNET-DRAFT November 2002
The purpose of this operation is to allow a client to get one or
more credentials from a server (the purpose of the entire protocol
really!).
The client sends a DownloadRequest message to the server which MAY
contain a credential selector string for the credential. No, or an
enmpty, credential selector means the request is for all credentials
associated with the account.
The server responds with a DownloadResponse or an error message. A
DownloadResponse contains one or more credential payloads including
the LastModified time which represents the time (at the server) when
the last change was made to each credential associated with the
account (e.g. subsequent to an UploadRequest).
2.3 Miscellaneous
2.3.1 Session security
Six SACRED operations are defined above. In this section we specify
the requirements for security for each of the operations (where
supported).
Operation Security REQUIRED
--------- -----------------
Information request NONE
Create account Server authentication,
Privacy, Integrity
Remove account Mutual authentication,
Privacy, Integrity
Modify account Mutual authentication,
Privacy, Integrity
Credential upload Mutual authentication,
Privacy, Integrity
Credential download Mutual authentication,
Privacy, Integrity
The security requirements can be met by several mechanisms. This
document REQUIRES credential servers to support TLS and DIGEST-MD5.
Clients MUST support DIGEST-MD5 and TLS with server authentication.
The mandatory-to-implement TLS cipher suite for SACRED is
TLS_RSA_WITH_3DES-EDE_CBC_SHA.
When performing mutual authentication using DIGEST-MD5 for the
client, DIGEST-MD5 MUST only be used "within" a TLS server-
authenticated "pipe", and MUST only be used only for client
authentication. That is, we do not use the DIGEST-MD5 security
services (confidentiality, integrity etc.).
Editor: Farrell [Page 6]
INTERNET-DRAFT November 2002
2.3.2 Handling multiple credentials for an account
When more than one credential is stored under a single account, the
client can select a single credential using the optional credential
selector string.
There is no concept of a "default credential" - all credentials MUST
have an associated selector unique for that account. The selector
is REQUIRED for upload requests and OPTIONAL for download requests.
If the selector is omitted in a download request it MUST be
interpreted as a request for all the stored credentials.
An empty selector string value (i.e. "") in a credential download
request, is to be interpreted as if the selector string were
omitted, i.e. a download request containing this is a request for
all credentials.
It is an error to have more than one credential stored under the
same account where both have the same credential selector string.
2.3.3 Common fields
All messages sent to the server MAY contain ProcessInfo values. This
field MAY be used by other specifications or for vendor extensions.
For example, a server might require clients to include a phone
number in this field. The information response message contains a
list of the types of ProcessInfo that the server supports. This
extensibility scheme is similar to that used in [XKMS] and [XBULK].
Where no specific response message is defined for an operation (e.g.
for UploadRequest) then the transport will indicate success or
failure.
All of the response messages defined here MAY contain a Status
string, containing a value intended for human consumption.
2.3.4 Credential Format
A number of messages involve the Credential element. It has the
following fields (all optional fields may occur exactly zero or one
times unless otherwise stated):
- CredentialSelector contains a string by which this particular
credential (for this account) can be identified.
- PayLoad contains either a ds:KeyInfo or some other form of
credential. Implementations MUST support the PKCS #15 form of
ds:KeyInfo defined below (the SacredPKCS15 element).
- LastModified is a string containing the time (at the server) at
which this credential was last modified.
- TimeToLive (optional) is a hint which clients SHOULD honor, which
specifies the number of seconds for which the downloaded
credential is to be usable.
Editor: Farrell [Page 7]
INTERNET-DRAFT November 2002
- ProcessInfo (optional) MAY contain any (typed) information that
the server is intended to process. If the server doesn't support
any of the ProcessInfo data, it MAY ignore that data.
- ClientInfo (optional) MAY contain any (typed) information that the
client is intended to process, but which the server MUST ignore.
If the client doesn't support any of the ClientInfo data, it MAY
ignore that data (e.g. if the ClientInfo is device specific).
3. BEEP Profile for SACRED
The protocol described in this memo is realized as a [BEEP] profile.
Future memos may define alternative versions of the BEEP profile for
SACRED. When a BEEP peer sends its greeting, it indicates which
profiles it is willing to support. Accordingly, when the BEEP client
asks to start a channel, it indicates the versions it supports, and
if any of these are acceptable to the BEEP server, the latter
specifies which profile it is starting.
Profile Identification: http://iana.org/beep/transient/sacred/bss
This profile URI is consistent with [TRANS].
Messages Exchanged during Channel Creation:
InfoRequest,
CreateAccountRequest,
RemoveAccountRequest,
ModifyAccountRequest,
DownloadRequest,
UploadRequest,
InfoResponse,
DownloadResponse,
error,
ok
Messages starting one-to-one exchanges:
InfoRequest,
CreateAccountRequest,
RemoveAccountRequest,
ModifyAccountRequest,
DownloadRequest,
UploadRequest
Messages in positive replies:
ok,
InfoResponse,
DownloadResponse
Messages in negative replies: error
Messages in one-to-many changes: none
Message Syntax: c.f.,Section 3
Editor: Farrell [Page 8]
INTERNET-DRAFT November 2002
Message Semantics: c.f., Section 2
Contact Information: c.f., the editor's address section of this memo
3.1 Profile Initialization
Because all but one of the operations of the SACRED profile have
security requirements (cf., Section 2.3.1), before starting the
SACRED profile, the BEEP session will likely be tuned using either
http://iana.org/beep/TLS
or
http://iana.org/beep/TLS followed by
http://iana.org/SASL/DIGEST-MD5
(Appendix B gives an example of tuning a BEEP session using DIGEST-
MD5).
Regardless, upon completion of the negotiation process, a tuning
reset occurs in which both BEEP peers issue a new greeting. Consult
Section 3 of [BEEP] for an example of how a BEEP peer may choose to
issue different greetings based on whether privacy is in use.
Any of the messages listed in section 3.2 below may be exchanged
during channel initialization (c.f., Section 2.3.1.2 of [BEEP]),
e.g.,
C: <start number='1'>
C: <profile uri='http://iana.org/beep/transient/sacred/bss'>
C: <![CDATA[<DownloadRequest ...>]]>
C: </profile>
C: </start>
S: <profile uri='http://iana.org/beep/transient/sacred/bss'>
S: <![CDATA[<DownloadResponse ...>]]>
S: </profile>
Note that BEEP imposes both encoding and length limitations on the
messages that are piggybacked during channel initialization.
3.2 Profile Exchange
All messages are exchanged as "application/beep+xml" (c.f., Section
6.4 of [BEEP]):
Role MSG RPY ERR
---- --- --- ---
I InfoRequest InfoResponse error
I CreateAccountRequest ok error
I RemoveAccountRequest ok error
Editor: Farrell [Page 9]
INTERNET-DRAFT November 2002
Role MSG RPY ERR
---- --- --- ---
I ModifyAccountRequest ok error
I DownloadRequest DownloadResponse error
I UploadRequest ok error
3.3 Error handling
The "error" message from Section 2.3.1.5 of [BEEP] is used to convey
error information. Typically, after flagging an error, a peer will
initiate a graceful release of the BEEP session.
The following BEEP error reply codes from [BEEP] are to be used:
code meaning
==== =======
421 service not available
450 requested action not taken (e.g., lock already in
use)
451 requested action aborted (e.g., local error in
processing)
454 temporary authentication failure
500 general syntax error (e.g., poorly-formed XML)
501 syntax error in parameters (e.g., non-valid XML)
504 parameter not implemented
530 authentication required
534 authentication mechanism insufficient (e.g., too
weak, sequence exhausted, etc.)
535 authentication failure
537 action not authorized for user
538 authentication mechanism requires encryption
550 requested action not taken (e.g., no requested
profiles are acceptable)
553 parameter invalid
554 transaction failed (e.g., policy violation)
The following SACRED-specific error reply codes can also be used:
code Meaning
==== =======
555 Extension (ProcessInfo) used not supported
556 Required extension (ProcessInfo) not present
557 StaleCredential (A bad LastModified value was
contained in an UploadRequest.)
4. IANA Considerations
If the IANA approves this memo for standards-track publication, then
the IANA registers the BEEP profile specified in Section 4, and
selects an appropriate standards-track URI, e.g.,
http://iana.org/beep/sacred/bss
Editor: Farrell [Page 10]
INTERNET-DRAFT November 2002
The sacred protocol SHOULD be run over port <<TBD>>.
The GSSAPI service name (required when using SASL) for this protocol
SHALL be "sacred".
5. Security Considerations
[REQS] calls for specifications to state how they address the
vulnerabilities listed below.
V1. A passive attacker can watch all packets on the network and
later carry out a dictionary attack.
- The use of DIGEST-MD5 and/or TLS counters this
vulnerability.
V2. An attacker can attempt to masquerade as a credential server
in an attempt to get a client to reveal information on line
that allows for a later dictionary attack.
- The use of server or mutual authentication counters this
vulnerability.
V3. An attacker can attempt to get a client to decrypt a chosen
"ciphertext" and get the client to make use of the resulting
plaintext - the attacker may then be able to carry out a
dictionary attack (e.g. if the plaintext resulting from
"decryption" of a random string is used as a DSA private
key).
- The use of server or mutual authentication counters this
vulnerability.
V4. An attacker could overwrite a repository entry so that when
a user subsequently uses what they think is a good
credential, they expose information about their password
(and hence the "real" credential).
- Server implementations SHOULD take measures to protect the
database. Clients MAY use the ClientInfo field to store e.g.
a signature over the Credential, which they then verify
before using the private component.
V5. An attacker can copy a credential server's repository and
carry out a dictionary attack.
- Server implementations SHOULD take measures to protect the
database.
V6. An attacker can attempt to masquerade as a client in an
attempt to get a server to reveal information that allows
for a later dictionary attack.
- The mutual authentication requirements of this protocol
counter this to a great extent. Additionally, credential
servers MAY choose to provide mechanisms that protect
against online dictionary attacks against user account
passwords, either by repeated access attempts to a single
user account (varying the password) or by attempting to
access many user accounts using the same password.
V7. An attacker can persuade a server that a successful login
has occurred, even if it hasn't.
- Client authentication prevents this.
Editor: Farrell [Page 11]
INTERNET-DRAFT November 2002
V8. (Upload) An attacker can overwrite someone else's
credentials on the server.
- Only if they know the account password already (thanks to
mutual authentication).
V9. (When using password-based authentication) An attacker can
force a password change to a known (or "weak") password.
- Client authentication counters this.
V10. An attacker can attempt a man-in-the-middle attack for lots
of reasons...
- Mutual authentication plus the encryption of subsequent
messages prevents this.
V11. User enters password instead of name.
- Since the DIGEST-MD5 mechanism is only used after TLS
tuning, the user's name is also protected.
V12. An attacker could attempt various denial-of-service attacks.
- No specific countermeasures against DoS are proposed.
If the CreateAccountRequest message were sent over a cleartext
channel (or otherwise exposed) then an attacker could mount a
dictionary attack and recover the account password. This is why the
server authenticated TLS transport is REQUIRED for this operation.
If someone steals the server database they can launch a dictionary
attack. If the dictionary attack is successful, the attacker can
decrypt the user's credentials. An attacker that has learned the
user's account password can also upload new credentials, assuming
the user is authorized to modify the credentials, because someone
who knows the user's account password is assumed to be the user.
However, if someone steals the server database and is unsuccessful
at obtaining the user's account password through a dictionary
attack, they will be unable to upload new credentials.
Credential servers SHOULD incorporate measures that act to counter
denial of service attacks. In particular, they SHOULD drop inactive
connections and minimize the use of resources by un-authenticated
connections. A number of recommendations are listed at [DDOS].
References
Normative:
[BEEP] Rose, M., "The Blocks Extensible Exchange Protocol
Core", RFC 3080.
[PKCS15] "PKCS #15 v1.1: Cryptographic Token Information
Syntax Standard," RSA Laboratories, June 2000.
[REQS] Arsenault, A., Farrell, S., "Securely Available
Credentials - Requirements", RFC 3157.
[RFC2026] Bradner, S., "The Internet Standards Process --
Revision 3", RFC 2026.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", RFC 2119.
[SASL] Myers, J., "Simple Authentication and Security Layer
(SASL)", RFC 2222.
Editor: Farrell [Page 12]
INTERNET-DRAFT November 2002
[DIGEST-MD5] "Using Digest Authentication as a SASL
Mechanism", Leach, P., Newman, C., RFC 2831.
[TLS] Dierks, T., "The TLS Protocol - Version 1.0", RFC
2246.
[XMLDSIG] Eastlake, D., et al. "XML-Signature Syntax and
Processing", RFC 3075.
[XMLSCHEMA] "XML Schema Part 1: Structures", D. Beech, M.
Maloney, N. Mendelsohn, and H. Thompson. W3C
Recommendation, May 2001. Available at
http://www.w3.org/TR/2001/REC-xmlschema-2-20010502/
Informative:
[DDOS] "Recommendations for the Protection against
Distributed Denial-of-Service Attacks in the
Internet",
http://www.iwar.org.uk/comsec/resources/dos/ddos_en.
htm
[TRANS] Rose, M., "A Transient Prefix for Identifying
Profiles under Development by the Working Groups of
the IETF", RFC 3349.
[XKMS] Hallam-Baker, P. (ed), "XML Key Management
Specification", http://www.w3.org/TR/xkms2/
[XBULK] Hughes, M (ed), "XML Key Management Specification -
Bulk Operation", http://www.w3.org/TR/xkms2-xbulk/
Acknowledgements
Radia Perlman (radia.perlman@xxxxxxx) and Charlie Kaufman
(ckaufman@xxxxxxxx) co-authored earlier versions of this document.
Michael Zolotarev (mzolotar@xxxxxxxxxx) did much of the initial work
adapting an earlier draft to the use of SRP (though SRP was
subsequently dropped, much of the framework survives). Marshall Rose
(mrose@xxxxxxxxxxxxxxxx) helped out a lot, in particular, with the
BEEP profile. And the following people were actively involved in the
mailing list discussions leading to this draft:
David Chizmadia (vze2729k@xxxxxxxxxxx),
Dave Crocker (dcrocker@xxxxxxxxxxxxxxx),
Lawrence Greenfield (leg+@xxxxxxxxxxxxxx),
Dale Gustafson (dale.gustafson@xxxxxxxx),
Mike Just (Mike.Just@xxxxxxxxxxx),
John Linn (jlinn@xxxxxxxxxxxxxxx),
Neal McBurnett (neal@xxxxxxxxxxxxxxxxx),
Keith Moore (moore@xxxxxxxxxx),
Bob Morgan (rlmorgan@xxxxxxxxxxxxxx),
Eamon O'Tuathail (eamon.otuathail@xxxxxxxxxxxx),
Magnus Nystrom (magnus@xxxxxxxxxxxxxxx),
Gareth Richards (grichards@xxxxxxxxxxxxxxx)
Of course, any and all errors remain the editor's responsibility.
Editor's Address
Editor: Farrell [Page 13]
INTERNET-DRAFT November 2002
Stephen Farrell,
Baltimore Technologies,
39 Parkgate Street,
Dublin 8,
IRELAND
Phone: +353-1-881-6000
Email: stephen.farrell@xxxxxxxxxxxx
Full Copyright Statement
Copyright (C) The Internet Society (date). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph
are included on all such copies and derivative works. In addition,
the ASN.1 module presented in Appendix B may be used in whole or in
part without inclusion of the copyright notice. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process shall be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns. This
document and the information contained herein is provided on an "AS
IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK
FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN
WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Appendix A: XML Schema
<?xml version="1.0"?>
<!--DOCTYPE schema PUBLIC "-//W3C//DTD XMLSchema 200102//EN"
"XMLSchema.dtd" [
<!ATTLIST schema
xmlns:sacred CDATA #FIXED "sacred-2002-11-17"
>
<!ENTITY sacred 'sacred-2002-11-17>
<!ENTITY % p ''>
<!ENTITY % s ''>
] -->
<schema
targetNamespace="sacred-2002-11-17"
xmlns:ds="http://www.w3.org/2000/09/xmldsig#";
Editor: Farrell [Page 14]
INTERNET-DRAFT November 2002
xmlns:sacred="sacred-2002-11-17"
xmlns="http://www.w3.org/2000/10/XMLSchema";>
<!-- extensibility holes -->
<complexType name="ProcessInfoType">
<sequence maxOccurs="unbounded">
<any namespace="##other"/>
</sequence>
</complexType>
<element name="ProcessInfo" type="sacred:ProcessInfoType"/>
<complexType name="ClientInfoType">
<sequence maxOccurs="unbounded">
<any namespace="##other"/>
</sequence>
</complexType>
<element name="ClientInfo" type="sacred:ClientInfoType"/>
<!-- Where to put authenentication information -->
<complexType name="AuthInfoType">
<choice maxOccurs="unbounded">
<element name="DigestMD5AuthInfo">
<complexType>
<sequence>
<element name="PasswordVerifier"type="base64Binary"/>
<element name="Realm" type="string" />
</sequence>
</complexType>
</element>
<any namespace="##other"/>
</choice>
</complexType>
<element name="AuthInfo" type="sacred:AuthInfoType"/>
<!-- authentication mechanism parameters -->
<complexType name="AuthParamsType">
<choice maxOccurs="unbounded">
<element name=" DigestMD5AuthParams">
<complexType>
<sequence>
<element name="Realm" type="string"
minOccurs="1" maxOccurs="unbounded"/>
</sequence>
</complexType>
</element>
<any namespace="##other"/>
</choice>
</complexType>
<element name="AuthParams" type="sacred:AuthParamsType"/>
<!-- Protocol messsages -->
<!-- "account handling" operations -->
<!-- Information request -->
<element name="InfoRequest"/>
<element name="InfoResponse">
<complexType>
<sequence>
<element name="Status" type="string" minOccurs="0"/>
Editor: Farrell [Page 15]
INTERNET-DRAFT November 2002
<element name="ServerId" type="string"/>
<element ref="sacred:AuthParams"/>
<element ref="sacred:ProcessInfo" minOccurs="0"/>
</sequence>
</complexType>
</element>
<!-- Create Account Request -->
<element name="CreateAccountRequest">
<complexType>
<sequence>
<element name="UserId" type="string"/>
<element ref="sacred:AuthInfo"/>
<element ref="sacred:ProcessInfo" minOccurs="0"/>
</sequence>
</complexType>
</element>
<!-- reomve account request -->
<element name="RemoveAccountRequest">
<complexType>
<sequence>
<element ref="sacred:ProcessInfo" minOccurs="0"/>
</sequence>
</complexType>
</element>
<!-- password change request -->
<element name="ModifyAccountRequest">
<complexType>
<sequence>
<element ref="sacred:AuthInfo"/>
<element ref="sacred:ProcessInfo" minOccurs="0"/>
</sequence>
</complexType>
</element>
<!-- "run-time" operations -->
<!-- DownLoad Request -->
<element name="DownloadRequest">
<complexType>
<sequence>
<element name="CredentialSelector" type="string"
minOccurs="0"/>
<element ref="sacred:ProcessInfo" minOccurs="0"/>
</sequence>
</complexType>
</element>
<!-- Download Response -->
<element name="DownloadResponse">
<complexType>
<sequence>
<element name="Status" type="string" minOccurs="0"/>
<element name="Credential" type="sacred:CredentialType"
maxOccurs="unbounded"/>
</sequence>
</complexType>
Editor: Farrell [Page 16]
INTERNET-DRAFT November 2002
</element>
<!-- Upload request -->
<element name="UploadRequest">
<complexType>
<sequence>
<element name="Credential" type="sacred:CredentialType"
minOccurs="0" maxOccurs="1" />
</sequence>
<attribute name="Delete" type="string" use="optional"/>
</complexType>
</element>
<!-- Credential related structures -->
<!-- A new ds:KeyInfo thing -->
<element name="SacredPKCS15" type="base64Binary"/>
<!-- credential -->
<complexType name="CredentialType">
<sequence>
<element name="CredentialSelector" type="string"/>
<element name="LastModified" type="dateTime"/>
<element name="Payload" type="ds:KeyInfoType"/>
<element name="TimeToLive" type="string" minOccurs="0"/>
<element ref="sacred:ProcessInfo" minOccurs="0"/>
<element ref="sacred:ClientInfo" minOccurs="0"/>
</sequence>
<attribute name="Delete" type="string" use="optional"/>
</complexType>
<!-- if base64Binary isn't in your schema editor then add this -->
<simpleType name="base64Binary">
<restriction base="string"/>
</simpleType>
</schema>
Appendix B: An Example of Tuning with BEEP
Here is what tuning BEEP for authentication and privacy looks like
using TLS and SASL's DIGEST-MD5:
L: <wait for incoming connection>
I: <open connection>
L: RPY 0 0 . 0 233
L: Content-Type: application/beep+xml
L:
L: <greeting>
L: <profile uri='http://iana.org/beep/SASL/DIGEST-MD5' />
L: <profile uri='http://iana.org/beep/TLS' />
L: <profile uri='http://iana.org/beep/transient/sacred/bss' />
L: </greeting>
L: END
I: RPY 0 0 . 0 52
I: Content-Type: application/beep+xml
I:
I: <greeting />
I: END
Editor: Farrell [Page 17]
INTERNET-DRAFT November 2002
I: MSG 0 1 . 52 158
I: Content-Type: application/beep+xml
I:
I: <start number='1'>
I: <profile uri='http://iana.org/beep/TLS'>
I: <![CDATA[<ready />]]>]]><![CDATA[
I: </profile>
I: </start>
I: END
L: RPY 0 1 . 233 121
L: Content-Type: application/beep+xml
L:
L: <profile uri='http://iana.org/beep/TLS'>
L: <![CDATA[<proceed />]]>]]><![CDATA[
L: </profile>
L: END
... successful transport security negotiation ...
L: RPY 0 0 . 0 186
L: Content-Type: application/beep+xml
L:
L: <greeting>
L: <profile uri='http://iana.org/beep/SASL/DIGEST-MD5' />
L: <profile uri='http://iana.org/beep/transient/sacred/bss' />
L: </greeting>
L: END
I: RPY 0 0 . 0 52
I: Content-Type: application/beep+xml
I:
I: <greeting />
I: END
I: MSG 0 1 . 52 143
I: Content-Type: application/beep+xml
I:
I: <start number='1'>
I: <profile uri='http://iana.org/beep/SASL/DIGEST-MD5'>
I: <blob />
I: </profile>
I: </start>
I: END
L: RPY 0 1 . 186 339
L: Content-Type: application/beep+xml
L:
L: <profile uri='http://iana.org/beep/SASL/DIGEST-MD5'>
L: <![CDATA[<blob>...</blob>]]>
L: </profile>
L: END
I: MSG 1 0 . 0 355
I: Content-Type: application/beep+xml
I:
I: <blob>...</blob>
I: END
Editor: Farrell [Page 18]
INTERNET-DRAFT November 2002
L: RPY 1 0 . 0 125
L: Content-Type: application/beep+xml
L:
L: <blob status='complete'>...</blob>
L: END
Appendix C: Provision SACRED using other Protocols
SACRED may be implemented in a non-BEEP environment, providing that
before any SACRED PDUs are sent, the application protocol must be
protected according to the security mandates provided in Section
2.3.
For example, if SACRED is provisioned as the payload of an
application protocol that supports SASL and TLS, then the
appropriate SASL and/or TLS negotiation must successfully occur
before exchanging Sacred PDUs.
Alternatively, if the application protocol doesn't support SASL,
then one or more PDUs are defined to facilitate a SASL negotiation,
and the appropriate negotiation must occur before exchanging Sacred
PDUs.
Appendix D: Changes & Open Issues
<<Note to RFC editor. Please remove this appendix and its TOC entry
prior to RFC publication.>>
Open Issues:
- None known:-)
-04:
- Replaced SASL-MD5 with DIGEST-MD5 everywhere
- Updated appendix B and other BEEP issues according to
Marshall Rose's Oct 6th recommendations
- Applied all but three "editorial corrections" raised on list,
see
- Added a recommendation to download prior to modify
- Fixed AuthXXXType extensibility as suggested by Gareth
Richards
-03:
- Should the DTD or schema be normative? I'd usually go for the
schema, but in this case the DTD seems much simpler.
- Deleted DTD
- Should we apply for a port number? (probably)
- Mailed IANA and added IANA considerations section.
- Multiple substrates issue
- Decided at Minneapolis (Spring 2002) not to change.
- Should we specify a max value where "unbounded" is in the
schema or "+"/"*" in the DTD?
- Nope.
- Remove SASL-SRP and replace with something else
Editor: Farrell [Page 19]
INTERNET-DRAFT November 2002
- Done - changed to DIGEST-MD5 (rfc 2831).
- SASL authorization identity issue
- Waited some time for text that didn't arrive and so leaving
current text as is.
- Changed away from having a request with an empty sequence
representing an implicit delete to where an explicit deletion
request indicator (an XML attribute) is required
- Added a service name: "The GSSAPI service name (required when
using SASL) for this protocol SHALL be "SACRED"." (Note: I
don't understand this and don't want to, but do let me know
if its wrong:-)
-02:
- Changes as per mailing list discussion:
- deleted (previous) section 2.4: session mgt & added sec.
cons about DoS
- Applied changes from the following threads:
- "BEEP adjustments"
- "MultipleCredentials"
- "SRP adjustments"
- "LastModified"
- Other changes:
- clarified how UploadRequest can delete one or more
credential payloads
- merged sections 2 and 3 since its much clearer that way
- changed Credential structure about a bit due to moving
LastModified
-01: Changes as per mailing list discussion:
- Change from authors to editor + acks
- Included resolved comments from list:
- password -> account pwd or cred pwd as appropriate
- account mgt separated and optional
- added example beep tuning
- selector: no default, omit in d/l means all
- changed LastModified scheme as per list comments
- Excluded administrative operations (was an open issue)
- Demoted hashed(username) concept to a note under security
considerations (see V11).
- Dropped idea of specifying a mapping between SRP id and cTLS
certificate.
- Dropped xkms & xbulk as normative references, but copied some
stuff from them.
-00: This version is adapted from draft-ietf-SACRED-protocol-beep-
pdm-00.txt, the main changes are:
- PDM -> SRP &/or TLS
- Payload security -> SASL or TLS
- Dropped username hashing
- Dropped away-from-home
Editor: Farrell [Page 20]